Share:

2004R FULL BILLET PRO STREET/STRIP TRANSMISSION

24RT/FBPSS
2004R FULL BILLET PRO STREET/STRIP TRANSMISSION

The 2004R PRO STREET/STRIP TRANSMISSION is recommended  for ultra high performance street and strip cars producing producing up to 550 hp and 500 lbs ft. and weighing up to 4000 lbs. It can also be used in lighter vehicles at power levels up to 800 hp and 800lbs.ft. in some applications.Perfect for low 11 to mid 9 second Turbo Buicks,as well as all small and big block Buick,Cadillac,Chevrolet,Oldsmobile and Pontiac vehicles.All of our 2004R transmissions are dynomometer tested and then in car tested and calibrated prior to shipment.

COMPETITION COMPONENTS:

3OOM STEEL BILLET INPUT SHAFT

E4340 STEEL BILLET REINFORCED OVERDRIVE CARRIER

E4340 STEEL BILLET REINFORCED OVERDRIVE RING GEAR

300M STEEL  BILLET SHAFT FORWARD DRUM

4130 HTSR STEEL BILLET BAND ANCHOR PIN

BILLET ALUMINUM OVERRUN CLUTCH PISTON

BILLET ALUMINUM DIRECT CLUTCH PISTON

BILLET ALUMINUM FORWARD CLUTCH PISTON

BILLET ALUMINUM LOW/REVERSE CLUTCH PISTON

BILLET ALUMINUM INTERMEDIATE SERVO PISTON

 



.CGOVERNOR SPRING ELIMINATES GOVERNOR SPRING EJECTIONAll DIRECT CLUTCH PISTON.ALUMINUM FORWARD CLUTCH PISTON.ALL NEW CLUTCHES AND STEELS.EXTRA WIDE 2ND GEAR BAND. UPDATED 3 CLUTCH OVERDRIVE PACK.METALLIC RED DIRECT CLUTCHES.101 THICK DIRECT STEELS AND .290" PRESSURE PLATEDUAL FED DIRECT CLUTCH TRIPLES CLUTCH APPLY PRESSUREPUMP MODIFICATIONS BLUEPRINTED FRONT PUMP.LAPPED PUMP FACES.CLEARANCED ROTOR AND SLIDE..555" CNC MACHINED TV BOOST VALVE. .296" CNC MACHINED INTERMEDIATE BOOST VALVE. HIGH RATE PRESSURE REGULATOR VALVE SPRING. PORTED PUMP DRAINBACK PASSAGES. INDUCTION HARDENED STATOR TUBE. STEEL PUMP VANE RINGS. HIGH TENSION PUMP SLIDE SPRINGS. INCREASED LUBE OIL TO REAR PUMP THRUST WASHER. ROLLERIZED COMPONENTS ROLLERIZED CENTER SUPPORT. ROLLERIZED LO/REVERSE CLUTCH HOUSING. ROLLERIZED REAR RING GEAR. ROLLERIZED DIRECT DRUM. ROLLERIZED FORWARD DRUM.Over time the factory metal thrust washers wear and as a result increase operating clearances and send debris through the transmission.All metal thrust washers in the transmission are replaced with high capacity low drag needle bearing assemblies.This is a time consuming process but definately beneficial for a performance transmission build.Internal components are machined in a lathe to create pockets for the bearings to locate in,as well as generate proper clearances.These bearings also reduce internal friction.This results in lower thrust surface operating temperature,and reduced horsepower loss. CALIBRATION UPGRADES EXCLUSIVE CK PERFORMANCE SEPERATOR PLATE DIRECT CLUTCH CORRECTION PACKAGE RECALIBRATED VALVE BODY AND GOVERNOR Over 20 years of research and development have resulted in the ultimate combination of performance and component durability.The main problem with this transmission at high power levels is the direct clutch.Our custom seperator plate removes flow restrictions that cause 2/3 upshift delay and friction element slip.Our revolutionary "3/2 Control Valve Delete" removes the infinitely variable orificing of 3rd accumulator oil to the servo release from the hydraulic system,and uses a single orifice.This is the real correction for direct clutch failure.Custom automatic shift valve body and governor combinations can give you the wide open throttle upshifts your vehicle needs.Calibrations can be made to allow wide open throttle shift points anywhere between 5000 and 6500 rpm's,without shift timing complaints at light or part throttle.

$3,799.00 /Each.
In Stock
Qty: